300Pcs Button Pin Maker Machine Multiple Sizes 1''+1.25''+2.25'' Badge Button Press Machine with Button Parts&Circle Cutter&Picture (Purple). 18.9 x 11.02 x 7.09 inches. 100 sets # 25mm Metal Pinback Button Refills, 25mm+32mm+58mm Molds, 3 pcs Circle Cutter, 3 metal pins, 100 sets # 32mm Metal Pinback Button Refills, 100 sets # 58mm Metal Pinback Button Refills, Manual, 2pcs L wrench, 1 x Button Maker Machine.
Button Maker Multiple Sizes: 1 inch(25mm), 1.25 inch(32mm), 2.25 inch(58mm). Comes with complete crafting materials for 300 button badges. Pay Attention To distinguish the small and medium molds, do not install the wrong mold.300 Pin-back Button Badge Kits: You can make 300 button badges(100pcs for each size). The complete packaging kit makes a total of 300 pin buttons. The included circle cutters make it possible to make your own pieces of paper in the desired size. Easy to Use: Makes a badge in less than 15 seconds after installation.
Please watch the using video or manual in detail before use. Plastic pinback buttons do not put a plastic washer in making(only the 1.25" and 2.25" metal pin backs require a washer). We have included extra 1.25'' and 2.25'' washers for you to use when making metal badges. Save Time and Energy: The badge button maker adopts the appearance of high-strength engineering plastic, the body and the mold are integrated, light weight and easy to operate. A top-rotating die not only improves efficiency and accuracy, but also facilitates better positioning. You will take less 15 seconds to make a badge when installed correctly. Creative Gift: DIY Personalized pin Badge. Can be used for photo storage, ornament decoration, wedding name tags, classroom crafting, etc. We look forward to more creative design showcases from you! Print your slogan and pin it on backpacks, scarves, hats, etc. Show your attitude on some important occasions.Great for kids party favors as well as handmade gifts. Unlike other obscure manuals on the market, we have the most complete manuals and installation videos. For more questions, please for immediate help.
1''+1.25''+2.25'' Button Maker Supplies. The entire button is made of 5 pieces (Clasp Pin, Metal Back, Metal Shell, Paper Graphic, Clear Plastic Cover). Our molds are suitable for button parts marked 1", 1.25" and 2.25 on the market. 1 x Button Maker Machine.1+1.25+2.25 inch Molds. 3 metal pins & 2pcs L wrench. You can create your own design, assemble the badges, and then hand them out or sell them as needed.
How Do You Get a Good Design on Your Button? With the right covers and backings, you should be able to use any round piece of paper and make a durable button. However, basic printer paper can lead to poor saturation and resolution images.Photo paper is better for more detailed images. Play around with ideas and make sure to cut your designs to the right diameter for the machine. Button Badge Size: 1'', 1.25'', 2.25'. There is a slide system for automatic positioning after properly installed.
Have two compartments for setting up and pressing buttons for a smoother process. After you are proficient, you can make a badge in about 10 seconds. You can make a total of 300 badges. 1''# 100pcs, 1.25''# 100pcs, 2.25''#100pcs. For any size plastic pinbacks, do not put a washer under it.
But for 1.25'' and 2.25'' metal pinbacks, DO NEED PUT A WASHER UNDER IT FIRST. Attention: Installing the molds are important steps. Please do not install the mold in the wrong orientation. In most cases, subsequent making failures are caused by mold installation errors, so please follow the instructions and videos to install. When crimping the metal cover, paper and plastic clear cover, the pegs on the top mold.
Do not go into the holes. (as shown in step 4). When crimping the pinback button with top pieces, the pegs. Need go into the holes. (as shown in step 7). Also, In this step, you need to use a little force to pull the handle to the end Some reviews said "It won't crimp the paper and plastic clear cover around the metal backing". The failure was due to a lack of force during the second crimp. For medium(1.25 inch) and large(2.25 inch) metal buttons, please put a plastic washer under the pinback first.But for any plastic buttons, do not put a washer under it (as shown in step 5). 300 Sets Button Making Supplies---You can DIY 300pcs Badges. Button Making Problems - Solved Common Crimping Problems. Your first thought is usually that the machine is broken or the parts are defective but it is extremely rare that either of these is the case. Uestion 1:"Why are my buttons coming apart" or Why is there plastic clear cover not tucked in on the side of my button?
Make sure there are no problems with the installation. If something goes wrong with the installation, all subsequent steps will fail. One of the most common causes is that your paper is too thick or too thin. We recommend using 24-28 pound copier paper. Your graphic has to be cut exactly and even.
It should not be bigger than the plastic clear cover and the edges need to be nice and even. You need to push the handle down with a bit of force in the last press. It is best to hold the handle tightly with your hands when pressing for the last time so that the upper and lower molds can be tightly combined with each other.
The top die may become loose after a long time of use. If the mold is loose, that's maybe the cause you failed pressing. Because the vertical force between the upper and lower molds cannot be applied when pressing. Tighten with an L wrench before installing the upper mold if it needs(Do not over-tighten, make sure the upper die can rotate properly). Don't forget to put the metal pin that holds the sliding mold fixing.
If there is no metal pin, the force of the upper and lower molds will not be uniform, which will cause the button to unsealed. Metal pin is easy to lose, so we've included a few extras for emergencies. Only put one piece of paper and plastic clear cover at a time, too thick material can cause jamming and seal failure. Since papers or plastic clear cover are easy to stick together, you may not notice how many layers are there when putting.
Only for the 1.25'' and 2.25'' metal-back buttons do need put a plastic washer under it, all plastic-backs do not. Estion 2:Why is my metal cap stuck inside the mold and won't seal after the last press? Please use an intact metal cover, not deformed.
Do not reuse failed metal cover. When the pinback button is put into the mold, the up and downside are wrong. The correct button is with the pin side down.
If the metal cap stuck inside the top mold, press again to let it off. 4.3 out of 5 stars. 4.2 out of 5 stars. Quantity of 1.25 inch.
Quantity of 2.25 inch. 2.25'' bottle opener button.
We offer the best prices around on high quality products. Our E-store includes media such as books, movies, music and games while offering electronics, toys, sporting apparel, clothing, tools, general home, garden items and more.
We are always working hard to ensure your package arrives as soon as possible. We do not accept P. Please provide a physical address. We try our very best to make sure every customer is completely satisfied.
If there's a problem, message us! We're happy to help.