Button Maker Machine Photo Pin Badge Maker Button Press Machine wit 600 Supplies

  
Button Maker Machine Multiple Sizes 600Pcs, Aiment Photo Pin Badge Maker 1+1.25+2.25 inch for Kids, Button Press Machine with 600 Sets Button Making Supplies & Cutter & Magic Book (Green, 25/32/58mm). Button Maker Machine for All Sizes --- We prepared a upgrade all-in-one button maker machine for you, comes with 3 sizes of molds: 25mm (1 inch) 32mm (1¼ inch) 58mm (2¼ inch).

It's brand new detachable design also allows you to replace other sizes of molds to make various button pin badges. Well Made & Durable --- Different from other metal button making machine (too heavy & easy to rust), our badge maker is made of high strength engineering plastic, very portable, easy operation & no rust. Perfect for making small gifts like pin badge, opener, keychain, etcs. Special Design --- This pin press machine upgraded in labor-saving and positioning design, so press more accurately and need less force to press. Easier to make hundreds of diy buttons in a short time, which fully exercise the child's practical ability.

Easy Operation --- (Notice: please ensure the installation direction of mold is right, or the pin badge will be pressed unsuccessful) There is a detailed instruction and operation video in the picture page to tell you how to install the molds and make badges. The whole operation process is very simple, believe you will learn it quickly. Comprehensive Kit, Ready to Use --- 1×detachable button maker machine, 3 × 25/32/58mm (1/1.25/2.25 inch) button molds, 1×magic book, 3× circle paper cutters, 300pcs × 32mm & 200pcs × 25mm & 100pcs × 58mm pin badge accessories (round pins parts, plastic films, blank circle paper). Specail Gift --- The button maker machine kit is a perfect gift for your children/wife/mother/friends.

You also could use this badge pins press machine to make various special & beautiful badge pins, and permanent record tourist attractions, food, pets, baby photos, medals, plants, anime characters, idol, halloween anniversaries, etc. If you make the button by following the correct instruction steps, the button making process would be so easy and perfect.

On the Step 5: Should not be aligned with the holes at first press. On the Step 7: Should be aligned with the holes at second press. You don't need to press the button maker machine with too hard power while making buttons. Please be careful while remove the mold above to avoid accident hurt to your hands or break your machine. Aiment Photo Pin Badge Maker 1+1.25+2.25 inch for Kids.

Don't be worried while accidentally encountered the following problems, there are some solutions may work for you. Q1: The button maker do not work?

Answer: 1Check if you installed the button maker mold correctly, the below mold should be installed by the right direction, the all-plastic mold should be at the left side of handle, and the plastic mold with metal around inside should be at the right side; 2Check if the screws of machine and button maker mold are tightened, if not, use the allen wrench to tighten them. Q2: Missing the plastic films or other button parts?

Answer: Please feel free to tell me, I will send you the missing parts or resend you a new kit for replacement. Q3: The plastic can not wrap around the button? Answer: 1 Check if you used over 1pc paper or plastic film; and check if the paper is too thick? The paper should be controled within 115-135g, and the plastic film should be about 0.05mm thick; 2 The pin should be misaligned with the hole at the first press, and the pin should be aligned with the hole at the second press. Q4: The handle of button maker machine is easy to break?

Answer: 1 The plastic button maker machine is durable enough, unless you press it with too big power; if you make the buttons according to the correct steps of instruction, you just press the handle with light power, then the button can be completed perfectly; 2 Please put the button maker machine on the flat hard desktop instead of the deformable plastic desktop, to avoid damage the button maker machine while operation. Q5: The instruction is not well, are there any videos to show how to make buttons? Answer: We have updated the instruction, you can upload it on the Amazon page, you can see it on the Product guides and documents part --- "User Manual (PDF)". And there are also several videos on the Videos part of Amazon Page to show how to use it.

Q6: Does it compatiable with the metal badges? Answer: Yes, it could be used to make metal badges, but you must add a gasket on the mold before the second press while making larger than 37mm metal buttons (right side mold of the handle). The gasket is not included in this kit, since all of our button back are plastic. Q7: The large size paper cutter cuts the circles too big you have to manually trim them down for them to fit? Answer: The cutting size of circle cutter could be adjusted as demand.

And the correct cutting sizes are as follows: 35mm circle paper for 25mm badge, 44mm circle paper for 32mm badge, 54mm for 44mm badge, 70mm for 58mm badge, 85mm for 75mm badge.