75mm 3 Button Maker Badge Press 100Pcs Circle Cutter Manual Making Machine

75mm 3 Button Maker Badge Press 100Pcs Circle Cutter Manual Making Machine. Button Maker Machine, badge making machine is made of cast iron and is durable.

Badge parts, solid die-cast aluminum frame work pieces and molds are interchangeable, its assembly is very simple, easy to operate, durable and low failure rate. Button machine is equipped with metal slide rails, you can complete the operation more accurately and quickly, thus making more badges in a short time. Suitable for schools, organizations, community activities and corporate gatherings. The unique button badge decoration is a beautiful gift for family and friends. Button Badge Maker Machine Button badge maker kit we offered features a set of dies that fit for making 75 mm button badges and comes with 100 sets circle button parts.

Perfect for making your personalized, unique and fashionable badges. Widely used for pin buttons, rope ties, key chains, bottle openers, etc. Specification Die Size: 7.5 cm (3 inch) Button Size: 7.5 cm (3 inch) Button Quantity: 100 Sets Base Size: 16 x 29 cm (6.3 x 11.4 inch) Handle Length: 30 cm (11.81 inch) Package Content 1 x Manual 1 x Button Maker 1 x Set of Dies 75 mm 100 x 75 mm Buttons (metal parts + plastic parts + clear covers) Some tips for you! Q: Cannot make the button well, and the top and bottom do not match. A: Check the size of the up iron piece and back cover, make sure the up iron piece is a little bigger than the back cover.

Q: How to press the two molds when you make a button? A: When press mold A, you need to keep a distance, don't let the upper column through the hole, but when press mold B, please let the column through the hole until it completely closed. Q: What things need to attention when you install the mold of the machine? A: When you install the mold, the pin of the two sides must be installed, and when you installed the two sides must be pushed to the end, so that the upper and lower molds can be aligned. Q: How to solve the shell not fully crimping around the back?

A: When you press B mold, you must press slowly and hard until it to the end, and pauses two more seconds, then the buttons will be made very well. If the pressure is lighter, or lightly pressed, the mold will rebound quickly when it is closed, and it will easily fall off. How to install the machine: 1.

Install the handle on the host; 2. Screw 2 black bolts to the base plate to fix the main body. Place the upper mold in the slot of the main body; 4. Slide the basic mold into the groove. Keep the upper mold in a high position by hand, and then slide the bottom mold to place the upper mold in the middle of the bottom mold of the main body; 5. Insert the positioning pin into the hole on the side; 6.

How to make a badge: 1. Use a round knife to cut out a circular pattern; 2.

Put the outside of the logo into the bottom mold; 3. Put the circular pattern on the outside of the badge; 4. Put the film on the circular pattern; 5. Put the inside of the logo into the bottom mold (the grooved side is on the top) 6. Press the outside of the badge, then move the basic mold, and then press it again to combine with the inside of the badge; (after pressing the outside of the badge, there is no need to manually remove the badge) 7.

The badge has been successfully assembled. 1 x Micro Chapter Maker 1 x mold 75 mm 1100 x 75mm micro-chapter (metal parts + plastic parts + transparent cover) 1 x Allen key 2 x pins 2 x screws 1Instruction. The item "75mm 3 Button Maker Badge Press 100Pcs Circle Cutter Manual Making Machine" is in sale since Monday, August 2, 2021. This item is in the category "Crafts\Multi-Purpose Craft Supplies\Crafting Tools\Badge/ Button Makers".

The seller is "bkmd1195" and is located in Dayton, New Jersey. This item can be shipped to United States.

Brand: Unbranded
MPN: D112944IBA81276
Die Size: 7.5 cm (3 inch)
Button Size: 7.5 cm (3 inch)
Button Quantity: 100 Sets
Base Size: 16 x 29 cm
Handle Length: 30 cm