25,32,58mm Button Maker Badge Punch Press Machine with 400pcs Badge Parts US. Button Mold Diameter: 25mm, 32mm, 58mm.
Material: High strength engineering plastics. Gross weight: 4.7 kg(10.4 lbs). Handle Length: 21.5 cm/8.5 inch. Product Size(L x W x H): 23.5 x 8 x 36.5 cm/ 9.3 x 3.1 x 14.4 inch. 100pcs 25mm Transparent Plastic Films.
100pcs 32mm Transparent Plastic Films. 100pcs 58mm Transparent Plastic Films. Button Maker Multiple Sizes: 1 inch(25mm), 1.25 inch(32mm), 2.25 inch(58mm).Comes with complete crafting materials for 300 button badges. Pay Attention To distinguish the small and medium molds, do not install the wrong mold. 300 Pin-back Button Badge Kits: You can make 300 plastic button badges(100pcs for each size). The complete packaging kit makes a total of 300 pin buttons. The included circle cutters make it possible to make your own pieces of paper in the desired size. Easy to Use: Makes a badge in less than 15 seconds after installation. Please watch the using video or manual in detail before use. The included pin buttons do not require a plastic washer in making(only the 1.25" and 2.25" metal buttons require a washer). Save Time and Energy: The badge button maker adopts the appearance of high-strength engineering plastic, the body and the mold are integrated, light weight and easy to operate. A top-rotating die not only improves efficiency and accuracy, but also facilitates better positioning. You will take less 15 seconds to make a badge when installed correctly. Creative Gift: DIY Personalized Badge.
Can be used for photo storage, ornament decoration, wedding name tags, classroom crafting, etc. We look forward to more creative design showcases from you! You can create your own design, assemble the badges, and then hand them out or sell them as needed.
How Do You Get a Good Design on Your Button? With the right covers and plastic backings, you should be able to use any round piece of paper and make a durable button.However, basic printer paper can lead to poor saturation and resolution images. Photo paper is better for more detailed images. Play around with ideas and make sure to cut your designs to the right diameter for the machine. The size of the button made: 1'', 1.25'', 2.25'.
The body is made of durable plastic and is lightweight at just 5 pounds. Can also be fixed on the table with screws. There is a slide system for automatic positioning after properly installed. Have two compartments for setting up and pressing buttons for a smoother process. After you are proficient, you can make a badge in about 10 seconds.You can make a total of 300 badges. 1''# 100pcs, 1.25''# 100pcs, 2.25''#100pcs. We opted for a more durable PP plastic back instead as the metal will rust when exposed to moisture over time. Attention: Installing the molds are important steps. Please do not install the mold in the wrong orientation.
In most cases, subsequent making failures are caused by mold installation errors, so please follow the instructions and videos to install. Button Making Problems - Solved Common Crimping Problems.Your first thought is usually that the machine is broken or the parts are defective but it is extremely rare that either of these is the case. Uestion 1:"Why are my buttons coming apart" or Why is there mylar not tucked in on the side of my button? Make sure there are no problems with the installation.
If something goes wrong with the installation, all subsequent steps will fail. One of the most common causes is that your paper is too thick or too thin. We recommend using 24-28 pound copier paper.
Your graphic has to be cut exactly and even. It should not be bigger than the mylar and the edges need to be nice and even. You need to push the handle down with a bit of force in the last press. It is best to hold the handle tightly with your hands when pressing for the last time so that the upper and lower molds can be tightly combined with each other. The top die may become loose after a long time of use.If the mold is loose, that's maybe the cause you failed pressing. Because the vertical force between the upper and lower molds cannot be applied when pressing. Tighten with an L wrench before installing the upper mold if it needs(Do not over-tighten, make sure the upper die can rotate properly). Don't forget to put the metal pin that holds the sliding mold fixing.
If there is no metal pin, the force of the upper and lower molds will not be uniform, which will cause the button to unsealed. Metal pin is easy to lose, so we've included a few extras for emergencies.
Only put one piece of paper and mylar at a time, too thick material can cause jamming and seal failure. Since papers or mylars are easy to stick together, you may not notice how many layers are there when putting. Estion 2:Why is my metal cap stuck inside the mold and won't seal after the last press?Please use an intact metal cover, not deformed. Do not reuse failed metal cover. When the pinback button is put into the mold, the up and downside are wrong.
The correct button is with the pin side down. If the metal cap stuck inside the top mold, press again to let it off. Simply return the item to us in 30 days in an unused condition.
But remember to keep the item clean, intact with all labels, or we won't accept your request. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls.Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy.
This item is in the category "Crafts\Multi-Purpose Craft Supplies\Crafting Tools\Badge/ Button Makers". The seller is "wrfdiy" and is located in this country: US. This item can be shipped to United States.